Perbandingan Hasil Perhitungan Volume Cut And Fill Menggunakan Metode Kontur dan Digital Elevation Model (DEM) Pada Pembangunan Kawasan Subang Smartpolitan
DOI:
https://doi.org/10.35569/3tb2v624Abstract
Subang Smartpolitan is an industrial development that optimizes space utilization and accelerates regional industrial growth, strengthening industrial competitiveness, and contributing to the Indonesian economy, particularly in Subang Regency. The overall project covers an area of ??2.700 ha, with a zone 10 area of ??approximately 300.000 m2. This research focused on calculating excavation and embankment volumes using original ground surface elevation data and planned ground surface elevation data using the contour method and a Digital Elevation Model (DEM). The comparison showed that the difference between the original volume calculated using the contour method and the cut volume (excavation) was 1.385,11 m³ (0,12%), and the difference between the calculated fill volume (embankment) was 4.754,91 m³ (1,16%). Meanwhile, the DEM method yielded a difference of 21.240,52 m³ (2%) in the calculated cut (excavation) volume, and 5.803,27 m³ (1,43%) in the calculated fill (embankment) volume. Therefore, it can be concluded that the contour method yields a smaller difference in the original volume compared to the DEM method.
References
[1] L. Fitriani, P. D. Yanti, N. E. K. Aprianto, A. B. Safitri, and H. U. Annabiilah, “Implementasi Kebijakan Pembangunan Industri,” Kaji. Ekon. dan Akunt. Terap., vol. 1, no. 4, pp. 264–278, 2024, doi: 10.61132/keat. v1i4.682.
[2] A. K. Dewantara, “Dampak Pengembangan Kawasan Industri Terhadap Sosial Ekonomi Masyarakat Kabupaten Nganjuk,” 2017.
[3] N. Delastri, “Pengembangan Kawasan Industri Pulau Baai untuk Peningkatan Pertumbuhan Ekonomi di Provinsi Bengkulu,” Bappenas Work. Pap., vol. 8, no. 1, pp. 23–47, 2025, doi: 10.47266/bwp.v8i1.391.
[4] M. F. Saihitua and U. Sunda, “Kawasan Industri sebagai Katalisator Ekonomi Daerah,” https://rm.id/baca-berita/ ekonomi-bisnis/265363/kawasan-industri-sebagai-katalisator-ekonomi-daerah, tanggal 20 April 2025, pp. 1–8, 2025.
[5] B. E. Supriyanto, “Inovasi Kebijakan Investasi untuk Mendorong Pertumbuhan Ekonomi Lokal,” https:// klc2.kemenkeu.go.id/kms/knowledge/inovasi-kebijakan-investasi-untuk-mendorong-pertumbuhan-ekonomi-lokal-ee601c80/detail/, diakses tanggal 13 Nopember 2024, pp. 1–7, 2024.
[6] D. Sagita Fitri, R. Gus Faozan, S. Nurkhasanah, and H. Noviarita, “Pengaruh Pengembangan Sektor Industri Terhadap Pertumbuhan Ekonomi Di Indonesia,” J. Rumpun Manaj. dan Ekon., vol. 2, no. 1, pp. 204–215, 2025, [Online]. Available: https://doi.org/10.61722/jrme.v2i1.3432
[7] Y. I. Simbolon and A. J. Saputra, “Analysis of the Volume of Excavation and Stockpiling in the Bicycle Path Development Works jl. RE. Martadinata Batam Using the Elevation Difference Method with Contractor Calculations,” J. Civ. Eng. Plan., vol. 4, no. 1, pp. 155–161, 2023, doi: 10.37253/jcep.v4i1.7640.
[8] D. Ernawan, M. S. P. Pratama, M. D. S. Assidiq, R. Agustriana, Rosalinda, and N. Yulandari, “Analisis Produktivitas Alat Berat Dalam Pekerjaan Cut and Fill Pada Pekerjaan Kawasan Industri Cikopo Kabupaten Purwakarta,” J. Kendali Tek. dan Sains, vol. 2, no. 4, 2024.
Downloads
Published
Issue
Section
License
Copyright (c) 2025 MESA (Teknik Mesin, Teknik Elektro, Teknik Sipil, Teknik Arsitektur)
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
